piksel
Helpline
ATLAS CONCENTRATED AGENT FOR TOUGH CEMENT DEPOSITS

ATLAS CONCENTRATED AGENT FOR TOUGH CEMENT DEPOSITS

ATLAS CONCENTRATED AGENT FOR TOUGH CEMENT DEPOSITS
P1  na ściany P1 na ściany
P2  na podłogi P2 na podłogi
P3  do wewnątrz P3 do wewnątrz
P4  na zewnątrz P4 na zewnątrz
N5  gąbka N5 gąbka

Product description

ATLAS CONCENTRATED AGENT FOR STRONG CEMENT DEPOSITS consists of a selected mixture of inorganic and organic acids.
Efficient, strongly concentrated – removes persistent fresh or old stains, hardened residues of mineral mortars.
Can be diluted depending on the type and the degree of soiling (maximum 1:10).

Main properties

  • removes old scale, salt efflorescence, rusty patches
  • for gres, tiles, clinker, concrete
  • removes tough stains of cement mortars from tools and equipment

Main parameters

    Density: 1,1 g/cm3 Temperature during application: from +5 °C up to +25 °C

PROPERTIES

Go top
 
Efficient, strongly concentrated – removes persistent fresh or old stains, hardened residues of mineral mortars.
 
Can be diluted depending on the type and the degree of soiling (maximum 1:10).

USE

Go top
Recommended for cleaning stains after any construction works (small and large renovation, new projects) where mineral mortars were used – plastering and bricklaying, thermal insulation, application of screeds, tiling, grouting, etc.
 
Recommended for removal of mineral mortars deposit from tools and equipment – concrete mixers, paddles, stirrers, trowels, floats etc.

TYPE OF STAINS AND DEPOSITS
 
cement and cement-lime plastering mortars
+
cement adhesives
+
cement grouts
+
gypsum
+
salt and lime efflorescence
+
rusty stains
+
sediments formed from minerals contained in water
+

TYPE OF CLEANED SURFACE*
 
ceramic tiles (glazed tiles, terracotta, porcelain, clinker)
+
stone tiles
+
steel, galvanized and lacquered steel sheet
+
plastics
+
stone masonry wall
+
paving sett
+

* in order to establish the product influence on a particular surface it is recommended to perform a trial application on a less exposed surface part.

TECHNICAL DATA

Go top
Density
1,1 g/cm3
Temperature during application
from +5 oC up to +25 oC

 

TECHNICAL REQUIREMENTS

Go top
Cleaning agent is not classified as a construction product. The product has been given the Radiation Hygiene Certificate.

CLEANING

Go top
Areas covered with deposits of cement or lime should be previously moistened with water.
It is recommended to use a brush or a sponge for the product application and for further cleaning. Depending on the substrate parameters, intensity and type of dirt, the product can be applied undiluted or as a water solution (see the table):
without dilution
salt efflorescence on surface of construction materials
without dilution
stains of the adhesives, grouts, plastering mortars etc.
from 1:3 up to 1:5
dirt and lime
from 1:5 up to 1:10
Areas particularly toughly soiled should be soaked with undiluted preparation and left for a few minutes. In order to improve the effect of cleaning it is advisable to use compresses or a foam. Then after, the soiling can be removed with a brush or a sponge. Then the surface should be washed with clean water or a slightly basic water solution. Repeat application if needed.

PACKAGING

Go top
Plastic containers: 1 l, 5 l.

IMPORTANT ADDITIONAL INFORMATION

Go top
 
- Product application on coloured mineral surfaces (e.g. concrete paving sett, cement grouts) can result in its permanent discolouration.
 
- On surfaces with mortars containing cement or lime, e.g. ceramic cladding with cement grouting mortar, the use of undiluted product can cause erroneous mortar washing off.
 
- In the case of cleaning absorbent (porous) surfaces which allow dirt penetration into the material structure, the soiling might be found difficult to remove.
 
- Room where product is applied can be used after airing until characteristic smell disappears.
 
- Wash the tools with clean water directly after use.
 
- Danger. Causes skin irritation. Causes serious eye damage. Harmful to aquatic life with long-lasting effects. Keep out of reach of children. Wear protective gloves/protective clothing/eye protection/face protection. IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses if present and easy to do – continue rinsing. Immediately call a POISON CENTER or doctor/physician. IF ON SKIN: Wash with plenty of soap and water. Take off contaminated clothing and wash before reuse. Wash with plenty of soap and water. Get medical advice/attention. Avoid release to the environment. Proceed in accordance with Safety Data Sheet.
 
- Transport and store in tightly sealed, original and labelled packaging in dry and cool room. Protect from high temperatures (above 30°C) and freezing – product freezes and irreversibly loses its performanceat temperature below 0°C. Protect from direct sunlight. Shelf life of the product is 24 months from the date of manufacturing shown on the packaging.
 
The above information constitutes basic guidelines for the application of the product and does not release the user from the obligation of carrying out works according to engineering principles and OHS regulations.
At the time of publication of this product data sheet all previous ones become void. An up-to-date technical product documentation is available at www.atlas.com.pl/en
Date of update: 2020-07-08

 

Go top
ATLAS CONCENTRATED AGENT FOR TOUGH CEMENT DEPOSITS
ATLAS CONCENTRATED AGENT FOR TOUGH CEMENT DEPOSITS

Current documentation