white acrylic interior paint

P1  na ściany P1 na ściany
P3  do wewnątrz P3 do wewnątrz
N7  pędzel N7 pędzel
N9  wałek N9 wałek
N10 natrysk N10 natrysk

Product description

Painting walls and ceilings indoors – decorative or protective.

Main properties

  • well coating
  • high yield
  • for walls and ceilings
  • matt, snow-white

Main parameters

  • quality coating - III (PN-89/C-81536)
  • scrub resistance (after 28 days) - Class 4 (PN-EN 13300:2002)
  • time of drying: min. 2 hours


Go top
Painting walls and ceilings indoors – decorative or protective.

Types of painted substrates – cement or cement-lime plasters, thin-coat mineral renders, gypsum plasters and top finishes,  polymer top finishes, plasterboards, wallpapers, rough walls of concrete, bricks, blocks, hollow blocks.


Go top
Vapour – permeable, Sd < 0.03 m ensures water vapour permeability.
Snow-white after drying.
Well coating.
Matt - coats the substrate irregularities.
Perfect for spray application – does not brighten after hydrodynamic spraying.


Go top
ATLAS  ecoFARBA  paint is manufactured on the basis of acrylic binder with addition of high quality fillers and chemical agents. ATLAS ecoFARBA  interior paint: maximum content of VOC in the product 29.9 g/l, allowable VOC content: 30 g/l.

approx. 1.45 kg/dm³
Brookfield viscometer
Paint preparation, substrate, and ambient temperature during work and paint drying
from +5 °C to +25 °C
Sd value
< 0.03 m (for double painting)
according to PN-EN ISO 7783:2012
Quality coating
Scrub resistance (after 28 days)
Class 4
(PN-EN 13300:2002)
Coat appearance
White, matt
Drying time until grade 3
(temp. 23 °C ± 2 °C, air relative humidity 55±5%)
Next coat application
after min. 3 h*

* Depending on thermal and humidity conditions in a room.


Go top
The product has been given the Hygiene Certificate by the National Institute of Hygiene and the Radiation Hygiene Certificate.


Go top
Substrate preparation
The substrate should be air-dry, free from cracks and layers which would impair the paint bonding, in particular dust, dirt, wax and grease. Thoroughly remove any old adhesion paints and other coatings of poor bonding to the substrate. Clean old emulsion paint coatings with water with addition of detergents and leave to dry. Minor defects (e.g. cracks or gaps) should be repaired and floated. ATLAS GIPS RAPID recommended for substrate surface repairs. Places infected with mould should be cleaned and protected with ATLAS MYKOS agent. Prime substrates of high absorptivity and absorbability or dusty ones with one of two priming emulsions (in each case the primer after drying should form matt surface):
- ATLAS UNI-GRUNT diluted with water in weight ratio 1:3 (emulsion : water),
On non-absorptive substrates, e.g. plasterboards or surfaces coated with emulsion paints, one can apply ATLAS BASE COAT PAINT without priming with priming emulsions. Prior to wallpapers painting one should check the quality of bond between the paper and the substrate. Painting poorly bonded wallpapers can cause formation of blisters. Plasters can be painted after full drying, not earlier than:
- cement and cement-lime plasters - after 3-4 weeks,
- gypsum plasters - after 2 weeks.
Paint preparation
The paint is delivered ready to use. It must not be mixed with other materials. Before use, mix well with low speed mixer with drill for paints in order to unify the consistency.
Paint dilution
For the first paint coating, so-called pre-coat, paint can be diluted with water in ratio: max. 0.5 l of water with 10 l of paint. Keep the same dilution ratio over the whole painted surface. Use undiluted paint for final painting.
Apply the paint upon prepared and stable substrate with thin and uniform coat. Paint can be applied with a roller, a brush or sprayed. It is recommended to use rollers made of microphase or polyacryl of 11 mm fiber length. Painting the ceilings should commence from the by-window zone and continued inwards. The paint should be applied at least two times. The first coat can be applied with ATLAS BASE COAT PAINT as well. The second coat may be applied when the previous coat fully dries (after min. 3 hours, depending on substrate, air temperature and relative humidity). Keep the same application direction for a particular coat. Technological breaks should be planned in advance, e.g. in the corners, etc. Apply the paint continuously and avoid breaks in application.

Data for spray application with aggregate GRACO CED
StMax II 595
Material preparation
60 mesh
200 bar


Go top
Coverage: up to 14 m²/ 1 l of paint with single painting of smooth surfaces. Actual coverage depends on the substrate absorptiveness.


Go top
·         Use paint of the same production date on an individual surface.
·         Air the room during painting and directly after until characteristic smell disappears.
·         Painting surfaces differing in structure may cause difference in the paint shade.
·         The tools must be cleaned with clean water directly after use, before the paint dries.
·         Keep out of reach of children. Follow the instructions of the Safety Data Sheet. Unconditionally use respiratory, eyes and hands protective equipment when spraying.
·         Transport and store the product in tightly sealed buckets, in dry conditions and positive temperatures (preferably on pallets). Protect against overheating. Shelf life in conditions as specified is 24 months from the production date shown on the packaging.


Go top
Plastic buckets: 5 l, 10 l
Pallet: 440 l in 10 l buckets, 400 l in 5 l buckets
The above information constitutes basic guidelines for the application of the product and does not release the user from the obligation of carrying out works according to engineering principles and OHS regulations.
At the time of publication of this product data sheet all previous ones become void.
Date of update: 2015-07-13
Go top
white acrylic interior paint

Current documentation