piksel
Helpline
ATLAS GRUNTO-PLAST

ATLAS GRUNTO-PLAST

contact coat for difficult substrates

ATLAS GRUNTO-PLAST
P1  na ściany P1 na ściany
P2  na podłogi P2 na podłogi
P3  do wewnątrz P3 do wewnątrz
P4  na zewnątrz P4 na zewnątrz
N7  pędzel N7 pędzel
N9  wałek N9 wałek

Product description

Primer for difficult substrates – improves bonding of adhesives, water- and damp proofing, finishing coats to substrates of low absorptiveness, to extremely smooth substrates or those coated with old PVC adhesives, paints, etc.

Main properties

  • strengthens substrates and improves bonding
  • on existing tiles, terrazzo, dados
  • on non-absorptive concrete, OSB boards
  • under adhesives, top finishes, water- and damp proofing
  • on walls and floors (also with heating systems)

Main parameters

  • consumption: approx. 0.3 kg of mass for 1 m²
  • well bonding – min. 1 MPa (to concrete)

USE

Go top
Primer for difficult substrates – improves bonding of adhesives, water- and damp proofing, finishing coats to substrates of low absorptiveness, to extremely smooth substrates or those coated with old PVC adhesives, paints, etc.
Improves bonding – strongly bonds to substrates and freshly applied layers.
Facilitates the application of subsequent layers – rough surface reduces the “slip” of the applied material.
Protects fresh layers against adverse effects of the substrate – forms chemical barrier between substrate and freshly applied layer, limits the influence of one upon the other – limits colour protrusion from the substrate and formation of stains on the surface of finishing coat.
Prevents wooden substrates from excessive damp – resulting from contact with freshly applied wet layer.

Types of primed substrates – non-absorptive substrates, e.g. concrete, old tiles, terrazzo, OSB board.
Types of subsequent layers – adhesives for tiles, plasters, screeds, finishing coats, WODER E, WODER W, WODER DUO or WODER S water- and damp proofing.

PROPERTIES

Go top
Contains aggregate – improves bonding owing to significant expansion of the effective surface between layers (forms rough surface).
Manufactured in white colour.

TECHNICAL DATA

Go top
ATLAS GRUNTO-PLAST is manufactured as a ready-to-use mass based on acrylic resins and quartz powders.

Density
approx. 1.5 g/cm³
Bonding to concrete
>1.0 MPa
Substrate and ambient temperature during work
from +5°C up to +30°C
Further work after priming
after approx. 24 hours

TECHNICAL REQUIREMENTS

Go top

The product is not classified as a construction material.

APPLICATION

Go top
Substrate preparation
The substrate should be dry, free from dust, dirt, oils, grease and wax. Remove any loose, poorly bonded layers before the emulsion application.
Mass preparation
ATLAS GRUNTO-PLAST is manufactured as a ready-to-use mass. It must not be mixed with other materials, thinned or thickened. Just before use, the mass should be mixed in order to unify the consistency.
Priming
Apply the mass upon the prepared substrate with uniform coat using a roller or a brush.
Application of finishing layers
Tiling, floating, water- and damp proofing can commence when mass fully dries, i.e. after approx. 24 hours since application.

CONSUMPTION

Go top
The average consumption is 0.3 kg of mass for 1 m².

IMPORTANT ADDITIONAL INFORMATION

Go top
• Clean the tools with clean water directly after use.
• During application and drying, the primed surface should be protected against direct sunshine, wind action and precipitation.
• Follow the instructions of the Safety Data Sheet.
• Keep in tightly sealed original and labeled containers. Keep in dry and cool places, protect against overheating (> 30 °C) and freezing - the product freezes and irreversibly loses its performance in temperature below 0 °C. Protect against direct sunshine. Incompatible materials: avoid contact with aluminum, copper and alloys of these metals. Shelf life in conditions as specified is 12 months from the production date shown on the packaging.

PACKAGING

Go top
Plastic buckets: 5 kg
Pallet: 625 kg in 5 kg buckets
 
The above information constitutes basic guidelines for the application of the product and does not release the user from the obligation of carrying out works according to engineering principles and OHS regulations.
At the time of publication of this product data sheet all previous ones become void.
Date of update: 2015-11-22
Go top
ATLAS GRUNTO-PLAST
ATLAS GRUNTO-PLAST
contact coat for difficult substrates

Current documentation