piksel
Helpline
ATLAS MIG 2

ATLAS MIG 2

fast setting adhesive for gres-porcelain tiles 2-5 mm (C1FTE type)

ATLAS MIG 2
P1  na ściany P1 na ściany
P2  na podłogi P2 na podłogi
P3  do wewnątrz P3 do wewnątrz
P4  na zewnątrz P4 na zewnątrz
W1  mrozoodporność W1 mrozoodporność
W2  wodoodporność W2 wodoodporność
N2  paca stalowa zębata N2 paca stalowa zębata
i  silnie wiąże gres z podłożem i silnie wiąże gres z podłożem
D1 grubość na ścianie 2-5mm D1 grubość na ścianie 2-5mm
D31 wejście po 4h D31 wejście po 4h

Product description

ATLAS MIG 2 is manufactured as a dry mix of high quality cement binder, aggregates and specially selected modifiers. Owing to the improved formula the product offers:
• short setting time – foot traffic and grouting just after 4 hours since the tiles fixing, which is expected wherever excluding the renovated surface from usage is problematic or impossible – banks, shops, railway stations, restaurants, outpatient clinics, corridors, communication routes; combination of the fast drying ATLAS UNI-GRUNT priming emulsion (drying time 2 h), ATLAS MIG 2 adhesive (setting time 4 h) and ATLAS ARTIS grout (setting time 3 h), allows pedestrian access already after approx. 9 hours since the substrate priming,
• extended open time - allows placing the tiles even 30 minutes since the mortar application – it can be once applied onto larger surface and therefore minimize the time of work,
• reduced slip, therefore enables fixing the cladding “from the top”, which helps to avoid cut-to-size tiles on exposed wall zones.

Main properties

  • foot traffic and grouting just after 4 hours
  • for small and medium size ceramic tiles, incl. gres-porcelain ones
  • extended open time – possibility of bonding up to 30 minutes since the adhesive application on the substrate
  • for bathrooms, kitchens, corridors
  • for indoor and outdoor use

Main parameters

  • consumption: approx. 1.5 kg of dry mix / 1 m² / 1 mm adhesive layer
  • bonding: min. 0.5 N/mm²
  • adhesive thickness: 2 - 5 mm

USE

Go top
Fixing ceramic cladding.

TYPE OF FIXED CLADDING
POSSIBILITY OF USE
glazed tiles
+
terracotta
+
porcelain-gres tiles
+
ceramic mosaic
+
concrete/ cement tiles
+

 Fixing small and medium size claddings.

SIZE OF FIXED ELEMENTS
POSSIBILITY OF USE
small and medium size tiles (< 0.1 m²)
+

 
Fixing the tiles on horizontal and vertical surfaces, indoors and outdoors.

PLACE OF USE
POSSIBILITY OF USE
residential buildings
+
rooms of small and medium operation loads in any building type
+
kitchen, bathroom, laundry, garage
+

 Fixing the cladding on standard substrates.

SUBSTRATE TYPE
POSSIBILITY OF USE
concrete
+
cement screeds and mortars
+
anhydrite screeds
+
cement, cement-lime and gypsum plasters
+
walls made of cellular concrete
+
walls made of silicate brick or hollow blocks
+
walls made of ceramic brick or hollow blocks
+
walls made of gypsum blocks
+

TECHNICAL DATA

Go top

Mass bulk density (after mixing)
approx. 1.65 kg/dm³
Mixing ratio (water/dry mix)
0.22 l / 1 kg
5.5 l / 25 kg
Min./max. adhesive thickness
2 mm / 5 mm
Adhesive preparation temperature, substrate
and ambient temperature during work
from +5°C to +25°C
Maturing time*
5 minutes
Pot life*
approx. 1 hour
Open time*
min. 30 minutes
Adjustability time*
10 minutes
Floor access/ grouting*
after approx. 4 hours
Full operational load – foot traffic*
after approx. 3 days
The time shown in the table is recommended for the application in the temperature 23°C and humidity 55% (approx.).

TECHNICAL REQUIREMENTS

Go top
The product conforms to PN-EN 12004+A1:2012 standard. EC Declaration of Performance No. 087/CPR. 

CE 0767
PN-EN 12004 + A1:2012
(EN 12004:2007 + A1:2012)
Cement adhesive for tiles, fast-setting,
of reduced slip and extended open time,
C1FTE type
for indoor and outdoor use,
for walls and floors
Reaction to fire – class
A1
A1fl
Bonding strength
- initial bonding
- early bonding (after ≤ 6 hours)
 
≥ 0.5 N/mm²
≥ 0.5 N/mm²
Durability - bonding after:
- heat exposure
- immersion in water
- freeze-thaw cycles
≥ 0.5 N/mm²
≥ 0.5 N/mm²
≥ 0.5 N/mm²
Open time - tensile adhesion after time not shorter than 20 minutes
≥ 0.5 N/mm²
Slip
≤ 0.5 mm
Release/content of hazardous substances
See: Safety Data Sheet

APPLICATION

Go top
Substrate preparation
The substrate should be:
stable – sufficiently sound, resistant to deformation, free from materials which would impair adhesion, stabilized.
even – maximum adhesive thickness is 5 mm, in case of larger irregularities use, e.g. ATLAS ZW 330 mortar, screeds ATLAS SMS, SAM or POSTAR.
clean – free from layers which can impair adhesion, especially dust, dirt, lime, oils, greases, wax, residues of oil and emulsion paints. The substrate coated with algae, fungi, etc. must be cleaned and protected with ATLAS MYKOS agent.
primed with:
- ATLAS UNI-GRUNT or ATLAS UNI-GRUNT PLUS – substrates of excessive or heterogenous
absorptiveness,
- ATLAS GRUNTO-PLAST – if the substrate absorptivity is low, or it is coated with layers limiting the adhesion.
 
Detailed guidelines concerning the substrate preparation, depending on its type. 

Substrate type
Preparation
Fresh cement screeds ATLAS POSTAR 80, ATLAS SMS 15 or ATLAS SMS 30
Stabilized min. 24 hours; optimum moisture content < 4% by weight.
Fresh cement screeds ATLAS POSTAR 20
Stabilized min. 3 days; optimum moisture content < 4% by weight.
Other cement screeds
Stabilized min. 28 days; optimum moisture content < 4% by weight. Prime with ATLAS UNI-GRUNT or ATLAS UNI-GRUNT PLUS.
Anhydrite screeds ATLAS SAM 55, ATLAS SAM 100, ATLAS SAM 150, ATLAS SAM 200 and SAM 500
Stabilized min. 2-3 weeks; optimum moisture content < 0.5% by weight. Prime with ATLAS UNI-GRUNT or ATLAS UNI-GRUNT PLUS. If, white surface tarnish forms during drying, it should be removed mechanically (grinded) and the surface dusted. Screed grinding accelerates the drying time.
Cement and anhydrite screeds on floor heating
Appropriately heated and primed with ATLAS UNI-GRUNT or ATLAS UNI-GRUNT PLUS.
Walls made of silicate or ceramic bricks and hollow blocks, cellular concrete
Leveling coat required (plaster). Direct fixing onto rough wall is possible in case of substrate appropriate dimensional tolerance. In such case it is necessary to execute full joint wall (or re-fill the joints) and repair any gaps or irregularities with ready-to-use mortars.
Prime with ATLAS UNI-GRUNT.
Cement and cement-lime plasters made of ready ATLAS mortars
Stabilized min. 3 days* for each 10 mm of thickness; optimum moisture content < 4% by weight.
Other cement and cement-lime plasters
Stabilized min. 7 days*. Prime with ATLAS UNI-GRUNT.
Gypsum plasters
Prime with ATLAS UNI-GRUNT. If the gypsum plaster is applied in a wet room it should be protected thoroughly against moisture. If damp has the form of short term action or average water splash, then the plaster should be coated with a preparation improving resistance against damp penetration, e.g. ATLAS GRUNTO-PLAST. In environment more subject to damp it is necessary to apply a watertight coating, e.g. ATLAS WODER E.
Concrete
Stabilized min. 21 days; optimum moisture content < 4% by weight. Remove remains of formwork oils and other substances which would impair adhesion obligatorily. Holes, cracks and other gaps should be filled with ATLAS BETONER system mortars.

*The time shown in the table is recommended for the application in the temperature 20°C and humidity 50% (approx.).
 
Adhesive preparation
Pour the adhesive from the bag into a container with the suitable amount of water (see Technical Data for ratio) and mix, using a low speed mixer with a drill for mortars, until homogenous. The dispersed adhesive should be left to rest for 5 minutes and then remixed. So prepared adhesive should be used up within approx. 1 hour.
Adhesive application
The adhesive should be applied onto the surface with a steel trowel and then distributed evenly and shaped (possibly in one direction) using a notched trowel. It is advisable to spread a thin adhesive coat first and then apply the coat of desired thickness and shape it with a notched trowel. It is recommended to lead a notched trowel in one direction. On walls, it’s recommended to shape
the adhesive in vertical direction.
Installing the tiles
After the application, the adhesive retains its properties for approx. 30 minutes (in temperature approx. 23 °C and 55 % humidity). Within this time, the tile must be placed and pressed well (the contact surface between the adhesive and the tile should be uniform and as large as possible – min. 2/3 of tile surface). Remove the excess of the adhesive pressed into the joints immediately. In case of floor tiles or tiling outdoors it is advisable to keep the full bonding surface (use the mixed method consisting in application of the adhesive on the substrate and the back of a tile, if needed). Keep the joint width appropriate for the tile size and operation conditions (check data in the sheets of ATLAS grouts).
Tile adjustment
The position of a tile can be adjusted with delicate moves along the bonding plane. It can be done within approximately 10 minutes since the tile is pressed (in temperature approx. 23 °C and 55 % humidity).
Grouting and cladding use
Foot traffic and grouting with ATLAS GROUT, ATLAS ARTIS GROUT, ATLAS DECORATIVE GROUT or ATLAS EPOXY GROUT can start after approx. 4 hours since the tiles fixing. The mortar reaches the operational strength after 3 days (check the Technical Data). Expansion joints, joints along the wall corners, at sanitary equipment, etc. should be filled with sanitary silicone ATLAS SILTON S or ATLAS ARTIS.

CONSUMPTION

Go top
Average consumption: approx. 1.5 kg of dry mix / 1 m² / 1 mm adhesive layer – for complete filling the space beneath the tile. It depends on the smoothness of the surface and the back side of the tile.

Tile size
Trowel notch size
[mm]
Thickness of
adhesive coat
[mm]
2/3 surface contact
[kg/m²]
Full surface contact
[kg/m²]
mosaic up to 2 × 2 cm
4.0
2.0
from 2.0
from 3.0
small size
up to 10 × 10 cm
≥ 6.0
2.0÷2.5
from 2.0
from 3.0
medium size
up to 30 × 30 cm
≥ 8.0
3.0÷3.5
from 3.0
from 4.5

IMPORTANT ADDITIONAL INFORMATION

Go top
• The tiles must not be soaked before fixing. When determining the adhesive thickness under the cladding, one should consider the geometric deviation of tiles shape, e.g. plane warpage. Tiles subject to discolouration in contact with grey cement should be applied with the use of adhesives based on white cement binder.
• When fixing the tiles on weak substrates whose bearing capacity is difficult to establish (e.g. dusty, difficult to clean), it is recommended to perform an adhesion test by fixing a tile and checking the bond after 48 hours.
• Higher air humidity or low temperature extend the setting time of the adhesive.
• Open time – from the moment of application of the adhesive to the moment of placing the tiles upon it – is limited. In order to check if it is still possible to fix tiles, performing a test is recommended. It consists in pressing your fingers against the adhesive. If the adhesive remains on the fingers, you may fix the tiles. If the fingers are clean, the old layer of the adhesive has to be removed and a new one applied.
• The tools must be cleaned with clean water directly after use. Difficult to remove residues of the set adhesive can be removed with the ATLAS SZOP agent.
• Contains cement. May cause respiratory irritation. Causes skin irritation. Causes serious eye damage. May cause an allergic skin reaction. Keep out of reach of children. Avoid breathing dust. Wear  protective gloves/protective clothing/eye protection/face protection. IF ON SKIN (or hair): Remove/Take off immediately all contaminated clothing. Rinse skin with water/shower. If skin irritation or a rash occurs: Get medical advice/attention. IF IN EYES: Rinse cautiously with water for
several minutes. Remove contact lenses if present and easy to do – continue rinsing. Follow the instructions of the Safety Data Sheet.
• The adhesive must be transported and stored in tightly sealed bags, in dry conditions (most preferably on pallets). Protect against humidity. Shelf life in conditions as specified is 12 months from the production date shown on the packaging. Content of soluble chromium (VI) in ready-to-use mix - ≤ 0.0002%.

PACKAGING

Go top
Paper bags: 25 kg
Pallet: 1,050 kg in 25 kg bags
 
 
The above information constitutes basic guidelines for the application of the product and does not release the user from the obligation of carrying out works according to engineering principles and OHS regulations.
At the time of publication of this product data sheet all previous ones become void.
Date of update: 2016-03-17
Go top
ATLAS MIG 2
ATLAS MIG 2
fast setting adhesive for gres-porcelain tiles 2-5 mm (C1FTE type)

Current documentation