BUILDING MORTARS
ATLAS KB-15
masonry mortar for cellular concrete
- for walls made of cellular and aerated concrete
- for blocks, bricks, hollow blocks
- for surface floating
- prevents thermal bridging
- compressive strength – category M5
ATLAS SILMUR
masonry mortars for silicate elements
- for walls made of silicates and cellular concrete
- white or grey
- for surface floating
- 4 classes of compressive strength
- can be used in low temperature (SILMUR M-15 only)
ATLAS REKORD
white cement top finish
- based on white cement
- for finishing walls and ceilings
- on typical mineral substrates
- contains fine aggregate – up to 0.2 mm
- reinforced microfibers
ATLAS PLASTERING MIX
traditional cement plaster, category III
- for plastering of walls made of ceramic, silicate brick, cellular concrete, concrete hollow blocks
- increased bonding
- plasticized, easy to apply
- layer thickness 6-30 mm
- plastering of walls and ceilings
ATLAS CEMENT SCRATCH COAT
scratch coat for 2- and 3-coat plasterwork
- improves plaster bonding to the substrate
- recommended beneath cement and cement-lime plasters
- reduces the material cost of plasterwork
- the highest standard-specified strength category
- for manual and machine application
ATLAS LIGHT MACHINE-APPLIED PLASTER
cement-lime plaster, category III
- for manual and machine application
- light – contains perlite
- high yield – up to 14 kg/m²/cm
- smooth – grain size up to 0.5 mm
- easily workable
ATLAS ZW 330
fast setting leveling mortar
- high bonding and compressive strength
- reinforced with polypropylene fibres
- plastic consistency
- under tiles, finishing coats, plasters, screeds
- tiling just after a few hours
ATLAS TEN-10
fast setting cement mortar
- - for repairs of concrete and ferroconcrete substrates
- for execution of floors exposed to high loads
- rapid strength build-up, limited contraction
- foot traffic already after 3 hours
- strong bonding to ceilings
ATLAS MONTER T-5
fast setting assembly mortar
- for anchoring of construction elements
- beginning of setting just after 5 minutes
- compressive strength after 1 hour not less than 10.0 MPa
- blocks local water leakages
- for non-structural repairs of concrete and ferroconcrete elements (mortar with addition of sand)
ATLAS MONTER T-15
fast setting assembly mortar
- for anchoring construction elements
- does not cause corrosion of steel elements
- strong adhesion to substrate
- grout under machines and equipment
- rapid strength build-up
ATLAS ADHER S
contact coat for concrete repairs
- high bonding to substrates
- contact coat for application underneath ATLAS screeds
- high content of corrosion inhibitors
- long-term reinforcement protection
- high bonding to concrete and steel
ATLAS FILER S
repair mortar for concrete, thickness 10-50 mm
- designed for repairs of single- and multilayer concrete or ferroconcrete substrates
- very high compressive strength, min. 60 MPa
- next layer of ATLAS FILER S applicable after 4 hours
- finishing coat application after 24 hours
- for manual and machine application
ATLAS ENDER S
finishing coat for concrete repairs, thickness 3-10 mm
- fine-aggregate
- designed for leveling concrete and ferroconcrete surfaces
- for filling cavities in prefabricated elements
- does not require application of contact coat
- for manual and machine application
- finishing coat applicable after 24 h
ATLAS MASONRY MORTAR
traditional masonry mortar
- for ceramic, concrete and silicate elements
- for joints 6-40 mm thick
- high plasticity
- compressive strength – category M5
- joins elements into stable, durable wall
ATLAS MASONRY MORTAR M10
traditional masonry mortar
- for ceramic, concrete and silicate elements
- for joints 6-40 mm thick
- high plasticity
- compressive strength – ≥ 10.0 N/mm²
- joins elements into stable, durable wall