Helpline

News

18/06/2018
/

Gel adhesive technology

ATLAS GEOFLEX is a highly flexible gel adhesive. Its recipe is an effect of cooperation between ATLAS R&D Department and contractors participating in numerous validations and testing. Owing to its unique operational and technical parameters as well as new plastic packaging, this new product in ATLAS portfolio is quickly becoming a hit on the market.

Manufacturers of adhesives are constantly seeking new solutions. Since the market expectations regarding these products are very high, it should not be any surprise. Contractors want products offering not only durability but also comfortable and quick use. It is the pressure of time and money which makes that contractors work at higher and higher temperatures and on more difficult substrates. In result they search for innovative technologies which provide safe and efficient work progress. Here comes our response – GEOFLEX – new, highly flexible gel adhesive.

The advantages of highly flexible gel adhesive ATLAS GEOFLEX:

2 in 1 – good spread and no slip even in case of large size tiles –  owing to very wide range of mix water volume (from 6.5 l up to 8.25 l per 25 kg of dry mix). It has been expanded in comparison to the range required by traditional adhesives. One may adjust the adhesive operational parameters to their own preferences and particular application area. Owing to this:

–          by adding the lowest recommended amount of water one obtains an adhesive with reduced slip and in result can fix the tiles “from top to bottom” without any support. This also applies to larger and thicker tiles.

–          increasing the amount of water enables to change the operational parameters; in result we obtain a pourable adhesive.

–          by adding the highest recommended amount of water one gets an adhesive which perfectly fills the space beneath large size tiles. It is particularly important in case of outdoor use. In parallel, gel adhesive properties do not cause the tiles pulling phenomenon (even large size tiles).

Thin-layer and thick-layer bonding and filling

The adhesive can be used within the range between 2 and 15 mm of layer thickness. It enables to fix the tiles either on thin or thick layer of adhesive. In addition, one can level uneven substrates. The combination of these factors significantly reduces the duration of tiling works. The contractor may use a single product both for fixing the tiles and filling uneven substrates either on walls or floors.

Perfect consistency

The second mixing is essential for the contractor, because it makes the adhesive elastic and smooth. GEOFLEX nicely sticks to a trowel and does not flow. Working with gel adhesive is a completely different experience in comparison to the conventional cement-based adhesives. It is not without reason that up to 80% of contractors, who had the opportunity to compare the operational parameters of our gel adhesive and cement adhesives during wide-scale validation tests, did admit that would probably never return to traditional cement-based adhesives.

Gel consistency and plasticity

An innovative technology of siliceous gel and special mixture of cements was used to create GEOFLEX. Owing to a special admixture based on minerals (e.g. montmorillonite), the adhesive obtains an elastic and gel consistency when mixed with water. This greatly simplifies the application as the adhesive sticks well to a trowel and can be distributed easily. What one cannot see with the naked eye is the inner water binding process. Aforementioned mineral additives bind water within their molecular structure. Water “stored” in such way is then used to carry out the reaction of adhesive binding – hydration. What is interesting, if we add water to pure mineral mixture, such prepared compound could bind five times more water than it weighs. This absorption would result in the increase of compound volume by 1500%. The additives in ATLAS GEOFLEX are selected so that they do not cause a significant increase of volume. The adhesive does not lose its volume during drying. In addition, neither there is shrinkage, nor pulling effect. There is no problem to fix the tiles on the following day.

Strength and flexibility

GEOFLEX adhesive belongs to class C2TE – it represents the adhesives of: improved bonding, extended open time and reduced slip according to the EN 12004:2007+A1:2012 standard. High bonding and durability make it possible to use this adhesive within a very wide range of application: in residential housing, but also in commercial, public access and healthcare buildings. Application area includes kitchens, bathrooms, laundry rooms, garages, terraces, balconies, loggias, as well as showers, car washes, rooms frequently washed with plenty of water, communication routes or compartments with low and medium operational loads. Detailed application area is listed in the adhesive technical data sheet on www.atlas.com.pl/en.

Perfect bonding to difficult substrates (including absorptive and insolated ones)

The improved water absorption of the mortar allows to fix tiles of any type – both absorbent and non-absorbent. The adhesive has also a greater tolerance in view of the substrates absorption. Owing to this, GEOFLEX provides full bonding also in case of substrates which were not prepared with proper diligence or on, so-called difficult substrates, such as concrete, terrazzo, old tiles (tile on tile technology) or OSB boards.

A very important adhesive feature, which results from the gel technology formula, is the possibility of application on substrates of increased temperature (e.g. screeds with underfloor heating or surfaces exposed to direct sunlight, such as balconies, terraces or loggias) – ambient temperature can reach up to 35°C. In these cases, the mortar achieves the declared parameters also under the conditions which are beyond the recommended temperature range for traditional adhesives (up to 25°C).

The adhesive does not pull the tiles in. On the contrary, it just increases the bond strength to the substrate. Owing to this, the tiling works can be easily continued on the following day. What is more, GEOFLEX has much higher adhesion in low temperature in comparison to traditional cement adhesives.

Extended open time

The test was to see how the adhesives perform under the conditions of progressive open time. It is more convenient for the contractor to prepare a larger area of wall or floor at once and then fix the tiles without any doubts concerning the bonding of the adhesive. There was an identical fragment of wall prepared for each of the adhesives. Then the adhesives of the same thickness were applied to the corresponding wall fragments. The test consisted in bonding the tiles and detaching them after 5 minutes. The result was given by the measured adhesion force of the adhesive. Subsequent tiles were bonded and detached from the substrate after a given time: 10, 15, 20, 25 and 30 minutes. Each time we measured the adhesion force.

Tiles attached to the fresh adhesive (open time: 0) presented high adhesion. The adhesive of S1 class performed the best here. Tiles bonded to the wall on which the adhesive dried for 5 minutes gave worse result than the first test by 0.1 MPa on average. More importantly, GEOFLEX result was almost identical with the one obtained by the adhesive of S1 class (0.325 MPa), while the result of the competitive adhesive X was only 0.2 MPa! Nevertheless, the biggest difference can be observed between 10. and 20. minute since the application of the adhesive onto the wall. In the 10. minute, one can see that GEOFLEX adhesion is 0.07 MPa higher than the one shown by popular adhesive of S1 class. The adhesives which were compared to ATLAS GEOFLEX showed large drop in adhesion, while GEOFLEX was characterised by small decline of this parameter. In practice, this means that GEOFLEX gives us more time to fix the tiles and that we can prepare a larger area of substrate at once.

Tight and durable packaging

The adhesive is packed in tight and weather resistant plastic bags. It is an innovation on the Polish market for this type of products. Plastic bags effectively protect the mortar from getting wet when the goods are stored and limit the rate of weathering of cement which they contain. In addition, they eliminate dust which can be annoying in case of traditional paper bags.

Grouting just after 12 hours

The process of binding the water in the adhesive structure leads to full hydration, even if the temperature of
substrate and environment is high. When the process is finished, the rest of water is drained and evaporated. Paradoxically, proper amount of water trapped in the adhesive accelerates the adhesive drying process. The adhesive has the optimum conditions and the drying process progresses steadily and continuously. The binding is faster and stronger. This makes it possible to enter the floor after 12 hours (at room temperature) and start grouting. The excess of water does not cause the efflorescence on the grout. The entire surface adheres well and is ready for the top finish. This enables a faster completion of a particular project.

Original text: Katarzyna Budzyńska-Kubiaczyk, ATLAS Group

English text: Piotr Marciniak, Michał Gosławski, ATLAS Group

Innovative technology of siliceous gel

– For the most difficult substrates
– 2 types of batched water = 2 consistencies
– Grouting just after 12 hours 
– Very good spread beneath a tile
– No slip even in case of large size tiles
– 3 in 1: filling/bonding/filling and bonding
– Can be applied at high temperature: 5-350C
– In a foil packaging!

 

80% of professionals who had the opportunity to compare the operating parameters of gel and cement adhesives admitted that they would never return to the traditional cement-based ones.