Helpline

BUILDING MORTARS

ATLAS KB-15 ATLAS KB-15
masonry mortar for cellular concrete
  • for walls made of cellular and aerated concrete
  • for blocks, bricks, hollow blocks
  • for surface floating
  • prevents thermal bridging
  • compressive strength – category M5
ATLAS SILMUR ATLAS SILMUR
masonry mortars for silicate elements
  • for walls made of silicates and cellular concrete
  • white or grey
  • for surface floating
  • 4 classes of compressive strength
  • can be used in low temperature (SILMUR M-15 only)
ATLAS REKORD ATLAS REKORD
white cement top finish
  • based on white cement
  • for finishing walls and ceilings
  • on typical mineral substrates
  • contains fine aggregate – up to 0.2 mm
  • reinforced microfibers
ATLAS PLASTERING MIX ATLAS PLASTERING MIX
traditional cement plaster, category III
  • for plastering of walls made of ceramic, silicate brick, cellular concrete, concrete hollow blocks
  • increased bonding
  • plasticized, easy to apply
  • layer thickness 6-30 mm
  • plastering of walls and ceilings
ATLAS CEMENT BASE COAT ATLAS CEMENT BASE COAT
base coat for 2- and 3-coat plasterwork
  • improves plaster bonding to the substrate
  • recommended beneath cement and cement-lime plasters
  • reduces the material cost of plasterwork
  • the highest standard-specified strength category
  • for manual and machine application
ATLAS LIGHT MACHINE-APPLIED PLASTER ATLAS LIGHT MACHINE-APPLIED PLASTER
cement-lime plaster, category III
  • for manual and machine application
  • light – contains perlite
  • high yield – up to 14 kg/m²/cm
  • smooth – grain size up to 0.5 mm
  • easily workable
ATLAS ZW 330 ATLAS ZW 330
fast setting leveling mortar
  • high bonding and compressive strength
  • reinforced with polypropylene fibres
  • plastic consistency
  • under tiles, finishing coats, plasters, screeds
  • tiling just after a few hours
ATLAS TEN-10 ATLAS TEN-10
fast setting cement mortar
  • for repairs of concrete and ferroconcrete substrates
  • for execution of floors exposed to high loads
  • rapid strength build-up, limited contraction
  • foot traffic already after 3 hours
  • strong bonding to ceilings
ATLAS MONTER T-5 ATLAS MONTER T-5
fast setting assembly mortar
  • for anchoring of construction elements
  • beginning of setting just after 5 minutes
  • compressive strength after 1 hour not less than 10.0 MPa
  • blocks local water leakages
  • for non-structural repairs of concrete and ferroconcrete elements (mortar with addition of sand)
ATLAS MONTER T-15 ATLAS MONTER T-15
fast setting assembly mortar
  • for anchoring construction elements
  • does not cause corrosion of steel elements
  • strong adhesion to substrate
  • grout under machines and equipment
  • rapid strength build-up
ATLAS ADHER S ATLAS ADHER S
contact coat for concrete repairs
  • high bonding to substrates
  • contact coat for application underneath ATLAS screeds
  • high content of corrosion inhibitors
  • long-term reinforcement protection
  • high bonding to concrete and steel
ATLAS FILER S ATLAS FILER S
repair mortar for concrete, thickness 10-50 mm
  • designed for repairs of single- and multilayer concrete or ferroconcrete substrates
  • very high compressive strength, min. 60 MPa
  • next layer of ATLAS FILER S applicable after 4 hours
  • finishing coat application after 24 hours
  • for manual and machine application
ATLAS ENDER S ATLAS ENDER S
finishing coat for concrete repairs, thickness 3-10 mm
  • fine-aggregate
  • designed for leveling concrete and ferroconcrete surfaces
  • for filling cavities in prefabricated elements
  • does not require application of contact coat
  • for manual and machine application
  • finishing coat applicable after 24 h
ATLAS MASONRY MORTAR ATLAS MASONRY MORTAR
traditional masonry mortar
  • for ceramic, concrete and silicate elements
  • for joints 6-40 mm thick
  • high plasticity
  • compressive strength – category M5
  • joins elements into stable, durable wall
ATLAS MASONRY MORTAR M10 ATLAS MASONRY MORTAR M10
traditional masonry mortar
  • for ceramic, concrete and silicate elements
  • for joints 6-40 mm thick
  • high plasticity
  • compressive strength – ≥ 10.0 N/mm²
  • joins elements into stable, durable wall
ATLAS MASONRY MORTAR FOR CLINKER ATLAS MASONRY MORTAR FOR CLINKER
masonry mortar with trass
  • improved resistance to efflorescence
  • does not stain the surface of bricks
  • for grouting walls made of clinker brick
  • based on filtrated aggregate